|
|
Post by spoonover on Dec 7, 2011 10:23:29 GMT -5
Show how you carry duplex loads when in the woods. Shooter posted one that was much better than my bag of unorganized loads. Thanks Shooter! This is how i carry a duplex loads around with me in the woods.  |
|
|
|
Post by Al on Dec 8, 2011 3:33:04 GMT -5
been on this board since the old green days, and never ceases to amaze me the creativity you guys come up with!
|
|
|
|
Post by rangeball on Dec 9, 2011 17:29:04 GMT -5
What are the black and white covers? What size cases?
|
|
|
|
Post by edwardamason on Dec 9, 2011 18:10:14 GMT -5
What are the black and white covers? What size cases? Ive seen those caps available at Harbor Freight and Lowes before. I cannot remember what they were intended to go on though. I think maybe those wire racks that you put in closets???To cover the ends so they do not cut you? |
|
|
|
Post by Al on Dec 10, 2011 4:10:37 GMT -5
see them in Mc Master Carr catalog, cap plugs, pull plugs, something like that.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Dec 10, 2011 11:21:57 GMT -5
|
|
|
|
Post by DBinNY on Dec 12, 2011 20:57:04 GMT -5
NAPA #715-1833 vacuum cap 1/4" red fits 7mm Rem Mag cases snuggly. Makes a perfect funnel and the main case body will not fall down a .50 or .45 bore. Got this from another board member years ago and has worked flawlessly since.
|
|
|
|
Post by kenny549 on Dec 13, 2011 8:46:08 GMT -5
I have carried loads in 7mm ultra mag casses with a foam earplug in the case neck and have never had one come out while carrying them in shirt pocket. The foam plugs expand after put in case neck and will work on many different calibers.
|
|
|
|
Post by shooter on Dec 16, 2011 10:12:59 GMT -5
What are the black and white covers? What size cases? Sorry guy i didn't see this sooner.I used a 7mm case and a 223 case for the powder and the cover are end cap cover for the metal self's from low or home depot.Hope this helps they sell them for like a 1.00 for like 4 in a little bag. Note if you put these together make sure you leave a gap between both brass that way you can refill them with out having to take them back apart.I leave just enough room to get my funnel on my powder pan between them. |
|
|
|
Post by edwardamason on Dec 16, 2011 14:18:36 GMT -5
The old Brown Butler Creek Speedloaders in .54 cal were partitioned in the middle and would make a excellent way of carrying your duplex loads. You would just need to mark the cap approriatly on which powder was which with a felt pen.
|
|
|
|
Post by esshup on Dec 17, 2011 9:33:05 GMT -5
I still like the plastic vials with the screw caps. I have a fleece "possibles" bag that has shell holder loops inside of it, and a couple of different compartments. Everything has it's place. I even use one of the vials to hold a bullet/sabot. I stuffed some tissue paper in it so the bullet doesn't rattle around.
|
|
|
|
Post by northny on Dec 19, 2011 9:45:35 GMT -5
Here is what I use. Made by Thompson Center it comes with with three long plastic tubes to carry three pellets of bp sub. I cut one plastic tube they come with down to hold two bullets with sabots. The vials I use for powder fit right in the holder and are held in by friction. Nice part is it holds the primers too. I have a couple of these, use for duplex or single powder loads  |
|
|
|
Post by edwardamason on Dec 19, 2011 14:06:50 GMT -5
Here is what I use. Made by Thompson Center it comes with with three long plastic tubes to carry three pellets of bp sub. I cut one plastic tube they come with down to hold two bullets with sabots. The vials I use for powder fit right in the holder and are held in by friction. Nice part is it holds the primers too. I have a couple of these, use for duplex or single powder loads That looks awesome. You got a part number for that? |
|
|
|
Post by northny on Dec 20, 2011 9:11:59 GMT -5
Thompson center part number is 8031. they are 7.99 at Midway arms their stock number 130783
|
|
|
|
Post by spoonover on Dec 21, 2011 11:45:08 GMT -5
Shooter, hope you don't care if I copied your speed loader! Made some from 223 case necked up to .284 cal and a 270 WSM case necked up to the former. Soldered the two cases as in the photo. Made a funnel from a 233 case cut and fitted to a flask funnel leaving the .233 case diameter for a nice fit for charging the empty cases. Ear plugs are working fine so no change here. Seems like plugs are holding, can't get snagged, pulled out, nor pushed in. Short mag case is fitting the BH 209 powder vial satisfactory.  |
|
