|
Post by artjr338wm on Mar 1, 2011 15:12:57 GMT -5
I have found a good 1 ton arbor press from Harbor freight for under $50, but am concerned if it will be strong enough for my purposes and not break.
I strictly need it to resize bullets I have knurled to a larger OD down to a smaller OD say from .451" knurled up to .4545/455" resized back down to consistently .4535-454", depending on what OD my 10ML-II likes best.
All the 2 ton arbor presses I have found cost at least almost 3x as much, so I am hesitant to spend that much more $$$ on a project I am not positive will work until I try it.
Any suggestions on where to get a good deal on a 2 ton arbor press would be extremely helpful. Al;l the ones I found cost from $130 to over $150 W/O S&H.
Thanks, Arthur.
|
|
|
Post by edge on Mar 1, 2011 15:20:02 GMT -5
1 ton should be fine.
With a 1 ton you should be able to size a .458 jacketed bullet to .448 in one pass.
You won't be able to size a .458 copper bullet in one pass...at least without a lot of effort.
edge.
Check ebay, sometimes there are good deals including shipping.
|
|
|
Post by artjr338wm on Mar 2, 2011 12:12:32 GMT -5
Thanks Edge, All I am looking to do is resize bullets knurled up to a OD of .4545-.455" down to .4535-.454".
My gole is to acheive as close to as is possible bullets that are 100% consistsnt in size, more than the actual OD itself. Thay could have a OD of .453, .4535, or even .454" it does not matter as long as it the same OD.
My situation is this. I get VG to EX accuracy with all copper TMZs and SFs, shot with sabots knurled up to any OD between .453-.4545". It is just each knurled OD will produce POIs that differ slightly and I wish to eliminate that from occuring. Using a press to resize them all to the same size +/- .005" strikes me as the easiest way to accomplish this, I hope.
Thanks, Arthur.
|
|
|
Post by boarhog on Mar 4, 2011 19:17:03 GMT -5
I bought a 2 ton arbor press from MSC. It takes a pretty good pull to size bullets more than .005. I tried to make a die to shrink 350 gr .510 bullets down for sabotless. I had to hammer the press arm down, but my die is far from finished.
Seems like I paid $70.00 for the press, but freight was a LOT!! Seems like over $50.00, but I'll have to dig into my invoice file to know for sure. BH
|
|
|
Post by Richard on Mar 4, 2011 21:53:51 GMT -5
|
|
|
Post by bigmoose on Mar 5, 2011 12:10:42 GMT -5
I have a one ton, if I was to do over again, I'd go with a two ton, but I'm not offering advice, Smokeeter, is the grand master of altering factory bullets, If I was about to buy a press, I'd PM him for his thoughts
|
|
|
Post by Jon on Mar 5, 2011 15:16:50 GMT -5
I'm sure this would be found funny by many but if you need more than 1 ton at that price you could buy a 10+ ton hydraulic press for the same money? Jon
|
|
|
Post by Richard on Mar 5, 2011 20:51:17 GMT -5
Jon........the only problem with using a hydraulic bottle jack is the fact that it is "slow" Now, if you have an air compressor, you could use a pneumatic/hydraulic jack which would be much faster. They have foot control for "up" and "release" Richard
|
|
|
Post by Jon on Mar 6, 2011 7:53:50 GMT -5
I have all of the above for my tubing bender. Just in the past to save room I didn't invest in the press since the arbor press did what I needed at the time.My compressor is big enough to handle my sand blaster. Jon
|
|