|
Post by deertroy1 on Jan 1, 2014 12:07:45 GMT -5
Not sure if it will help but my bedding job is complete. Everything went off without a hitch. Now I just need to let the Devcon completely cure for 7 days before I tighten everything down.
|
|
|
Post by muzzleman 54 on Jan 1, 2014 12:11:51 GMT -5
nice job !
|
|
|
Post by 7mmfreak on Jan 1, 2014 12:30:30 GMT -5
Nice job! Looks better than some I've seen guys pay for.
|
|
|
Post by hunter on Jan 1, 2014 12:43:19 GMT -5
Nice job, The first time makes you worry a little until you get the action out.
|
|
|
Post by deertroy1 on Jan 1, 2014 12:45:28 GMT -5
Yes it does. I've done a few centerfires with Acraglas but this is my first time using Devcon. It seems like pretty good stuff.
|
|
|
Post by donw28 on Jan 1, 2014 13:00:54 GMT -5
Devcon is wonderful for bedding and you did a great job. I normally recess above the pillars to remove the bedding to the outside diameter of the pillar with a drill press but that might be overkill. Maybe some of the guys with more experience will chime in. I suspect it will be fine as is and I hope it shoots better for you.
Don
|
|
|
Post by dannoboone on Jan 1, 2014 13:02:07 GMT -5
Great lookin' job. Congratulations! You will know for sure when you reassemble everything and checking the trigger for center and straightness. I'm working with one right now in which the slot for the trigger was milled off-center. Ain't no way it's ever going to look right upon close inspection! Nice job, The first time makes you worry a little until you get the action out. A LITTLE? My first actually turned out like Deertroy's but the anticipation/fear was hard on the ol' heart!
|
|
|
Post by 7mmfreak on Jan 1, 2014 13:24:50 GMT -5
I normally recess above the pillars to remove the bedding to the outside diameter of the pillar with a drill press but that might be overkill. I bed with the pillars screwed onto the gun so there is metal to metal and no epoxy between.
|
|
|
Post by deertroy1 on Jan 1, 2014 14:55:35 GMT -5
My receiver set pretty straight in the stock. I made two bolts without heads screwed into the receiver and this allowed me to place the receiver in the stock, using the existing pillars, and lined things up nicely. I recessed an area of wood around the pillars before applying the Devcon. However, my gun isn't technically pillar bedded or at least not to the point of 7mmfreak's. It should be a vast improvement, however, as it didn't seem like the recoil lug was even in contact with the stock before?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 1, 2014 15:06:18 GMT -5
Nice work, hopefully it helps and I'm sure it will.
|
|
|
Post by Richard on Jan 1, 2014 18:13:39 GMT -5
Great job Deertroy! Don't worry about the Devcon on the tops of the pillars.............You Done Good! Richard
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 1, 2014 20:15:34 GMT -5
yes very good job, you might want to check the tang and make sure its not making contact with the wood. the savage tang needs to float for best results..
|
|
|
Post by 10ga on Jan 1, 2014 20:42:08 GMT -5
Looks good. If tang OK all should be good to go. For a sure cure I keep my bedding jobs in a very warm place to cure, heat cures epoxy faster and cool cures slower. I use an electric blanket on the bed in the kids bedrooms, she has been gone for 13 years but brings the grand kids back often, and just wrap the stock in an old blanket and put on top of the electric blanket and turn it on and leave it for 24 to 48 hours, then it's well done. Sorta like when I do repairs/epoxy on the boat and put the halogen lights up close to speed the cure.
|
|
|
Post by deertroy1 on Jan 2, 2014 13:19:26 GMT -5
Thanks for the info guy's. I didn't know about the tang. I'll make sure and check it out!
|
|
|
Post by Richard on Jan 2, 2014 21:37:31 GMT -5
When I bed the Savages I generally put two layers of masking tape across the stock where the end of the tang sits. That way you know you will have clearance after bedding. Richard
|
|
|
Post by deertroy1 on Jan 3, 2014 11:07:52 GMT -5
I checked and the only place that is touching the stock is a small area about 3/8" square directly behind the bolt and the same area on the opposite side. Very little sanding would correct it but I think I'll shoot it first and see how it goes.
|
|
|
Post by basscat13 on Jan 4, 2014 9:41:54 GMT -5
Great job.
|
|